RETIRED ›
This product is no longer available. Some accessories, replacement parts, or services may still be available.
CS471 Compact Bubble Water Level Sensor, High Accuracy
Services Available
Repair Yes
Calibration Yes
Free Support Yes

Visão Geral

The CS471 is a high-accuracy bubbler (±0.02 ft) that generally measures ground or surface water level, but can also measure any liquid level. A Campbell Scientific data logger controls the CS471 pump and calculates the measurements. This compact bubbler typically communicates with the data logger via the SDI-12 protocol. Many of our data loggers support SDI-12.

Leia mais

Benefícios e Características

  • Ideal for areas where submersed sensors can be damaged due to corrosion, contamination, flood-related debris, lightning, or vandalism
  • Compatible with most Campbell Scientific data loggers
  • Easy to maintain
  • Robust pump design provides reliable operation
  • Consistent accuracy ensured by drift-free measurements and offset compensation using relative measurement
  • Purge function clears the measuring tube and the bubble chamber of contamination
  • Does not use pressurized nitrogen tank—requiring less frequent attendance
  • Existing tubes can be used

imagens

Descrição Técnica

The CS471 contains a piston pump that compresses air. The compressed air flows through a measuring tube into the water being measured. The pressure created in the measuring tube is directly proportional to the water column above a bubble chamber. The CS471 measures both barometric pressure and bubble pressure, one after the other. The height of the water above the bubble chamber is then calculated by taking the difference between the barometric and bubble pressure measurements.

To use the CS471, the acquisition system must include the measuring tube, a bubble chamber, power supply, data logger, and data logger connection cable. Campbell Scientific offers the measuring tube, bubble chamber, and cable as Common Accessories. (See the Ordering Info on the web page.) The CS471, data logger, and power supply must be housed in a desiccated environment, typically a Campbell Scientific enclosure. Hardware for mounting the CS471 to an enclosure backplate is shipped with the sensor.

The CS471 can communicate via SDI-12, 4 - 20 mA, or RS-485 (SDI-12 protocol via a physical RS-485 interface). SDI-12 is the preferred protocol when using Campbell Scientific data loggers. Many of our data loggers support SDI-12.

Especificações

Resolution 0.003 ft /0.014 psi
Power Requirements 10 to 30 Vdc
Measurement Time 1 min
Outputs SDI-12 (version 1.3) 1200 Baud, 4-20 mA, RS-484 (SDI-12 Protocol via RS-485 interface)
Measurement Range 0 to 15.2 m (0 to 50 ft)
Operating Temperature Range -20° to +60°C
Storage Temperature Range -40° to +85°C
Relative Humidity Range 10% to 95% RH (non-condensing)
Accuracy
  • ±0.003 m (0.01 ft) at 0 to 4.6 m (0 to 15 ft)
  • ±0.065% of reading at 4.6 to 10.7 m (15 to 35 ft)
  • ±0.006 m (0.02 ft) at 10.7 to 15.2 m (35 to 50 ft)
Measurement/Communication Current (Typical)
  • 320 mAh/day (1-minute query interval)
  • 25 mAh/day (15-minute query interval)
Maximum Tube Length 100.6 m (330 ft)
Electronics Box Dimensions 16.5 x 20.5 x 11.5 cm (6.5 x 8.1 x 4.5 in.)
Weight 1.5 kg (3.3 lb)

Documentos Relacionados

Compatibilidade

Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.

Data Loggers

Product Compatible Note
21X (retired)
CR10 (retired)
CR1000 (retired)
CR10X (retired)
CR200X (retired)
CR206X (retired)
CR211X (retired)
CR216X (retired)
CR23X (retired)
CR295X (retired)
CR3000 (retired)
CR500 (retired)
CR5000 (retired)
CR510 (retired)
CR800 (retired)
CR850 (retired)
CR9000 (retired)
CR9000X (retired)

Perguntas Frequentes Relacionadas

Number of FAQs related to CS471: 9

Expandir todosRecolher todos

  1. Is the only difference between the CS470 and the CS471 in their accuracy?

    Yes.

  2. What should be done to prevent a CS470 or CS471 from being damaged by the current of a river?

    Place the CS470 or CS471 above the high-water mark, and run the tubing into the water. Because the tubing is the only portion of the sensor in contact with the water, the sensor itself won’t be damaged by the current. It may be necessary, however, to replace damaged tubing occasionally.

  3. Do the CS470 and the CS471 require a separate gas pump or gas bottle to drive the system?

    No. These sensors do not need a gas bottle, and a pump is included with them.

  4. Do the CS470 and CS471 have the same measurement range?

    The measurement range is the same: 15.24 m (50 ft) of water. The CS471, however, is more accurate.

  5. Can a CS470 or CS471 be used to measure rainfall if the majority of the time there is no water to be measured?

    Yes.

  6. Using a CS470 or CS471, how can bad measurements be prevented because of river silt or mud?

    Terminate the tubing in a stilling well to greatly mitigate the effects of deposition. If this is not possible, use pn 25502, OTT EPS-50 Bubble Chamber. 

  7. What is the maximum length of tubing that can be used with a CS470 or CS471?

    100.6 m (330 ft).

  8. Can the 4 to 20 mA analog output on the CS470 or the CS471 be used with a PLC instead of a Campbell Scientific data logger?

    Yes, as long as the PLC is able to read 4 to 20 mA signals.

  9. How large of an enclosure is needed to house a CR1000, a 12 V battery, and a CS470 or CS471?

    The smallest enclosure that will accommodate these items is our ENC14/16.

Visite a FAQ Biblioteca